Mar 05 , 2023
The answer to your question, in a nutshell, is that a reglaze will last between 10 and 15 years. The longer answer is that the longevity of the glaze and finish of your bathtub depends on several other elements as well.
The integrity of your bathtub can be preserved through the process of refinishing. However, regular weekly cleaning and maintenance attention is essential to keep moisture and undesirable agents, such as mold, from eroding your finish and potentially destroying your bathtub. If you take the necessary precautions, your reglaze should last between 10 and 15 years. In that case, you should expect your reglaze's lifespan to be between three and four years.
How to consistently take care of your bathtub after reglazing
When taking care of a bathtub that has been reglazed, it is strongly recommended that abrasive cleaning products be avoided. When you clean your bathtub with abrasive cleansers like steel wool, bleach, or harsh detergents, you will remove a significant portion of the protective characteristics that the finishing paint provides, leaving your bathtub vulnerable to the environment. Due to the lack of a protective coating on its surface, this action will, over time, cause irreparable damage to your bathtub.
Instead of using abrasive cleaners, such as harsh detergents, soap, and baking soda, you should consider switching to non-abrasive alternatives. Eventually, any chemical compound will destroy the finish of your bathtub. Non-abrasive cleansers, on the other hand, will allow your bathtub's surface to remain protected for at least ten years, whereas abrasive cleaners will begin to erode the finish after only two to three years.
Reglazing your bathtub is a straightforward technique that can significantly extend the appliance's useful lifespan. The technique is straightforward but could be a bit confusing for first-time homeowners, but when finished correctly, your bathtub can easily last another 10-15 years. It's vital to explore this alternative the next time you want to replace an existing tub.
Preventative Measures and Upkeep in General
Before utilizing your tub or sink, make sure you wait for the required drying time.
When putting things away, it is better to avoid putting objects directly on the finish. This includes things like bottles, rags, and soap.
Do not use bathmats with suction cups underneath. The finish may sustain damage as a result of pulling and tearing when these are removed. If the cups are not removed, there is a possibility that condensation will accumulate underneath them. Bath Magic is the place to go if you want to purchase bath mats that are suitable for the surface that has been recently reglazed.
Be sure to keep any sharp objects or harsh chemicals safe from the surface you have reglazed. Before stepping into your bathtub, requesting visitors take their shoes off is polite.
Keep the caulking surrounding the tub in good condition. If you do not take this precaution, the wall of your home may sustain water damage, which will require expensive repairs.
You mustn't pick at the dust that is on the surface with your finger. If you follow up with your usual cleaning and use of the room, any surface dust should be gone within three to four weeks.
Under NO circumstances should any kind of tape be applied to the reglazed surface.
After every single application: cleaning
Make it a routine to scrub the bathtub after each use so that unattractive stains and soap scum do not build up and require additional cleaning. This will save you time and effort in the long run. To do this operation, all that is required is to empty the bathtub, wipe it down with a clean towel, and then rinse it out. U
se liquid soap to wipe surfaces once a week to remove any lingering grime. After each use of the bathtub, you should dry it thoroughly with a squeegee to eliminate any trace of water that may have been left on the surface of the tub. This will help prevent the development of mold in the bathroom. If you put in a small amount of effort today, you won't have to put in much effort later.
Our Tub Cast Ekopel Can Tackle Any Problem
Do you see a reddish tint after applying Ekopel?
The product had yellowish streaks because it was not fully combined or for a sufficient amount of time, which contributed to the problem. Yellow is used for the spots because they will be on top when Part B floats to the surface. You might try removing the stains with baking soda or with a Mr. Clean magic eraser, both of which are options. That is the only thing that we have tried that has been effective in eliminating the yellow stains from the item.
After dropping a heavy object into the bathroom sink by mistake, you noticed that one of the tiles had broken off. What course of action you ought to take?
The chip requires frequent replacement and maintenance in a hurry. If this step is neglected, it is possible for water to leak through the chip and under the paint, causing the Ekopel to peel off. Use our Ekopel Touch-Up Kit so that the chip can be repaired and good as new!
Have we reached the point where the product may be considered solid?
Tub Cast Ekopel dries in 24-36 hours. When you have completed the process of combining Part A and Part B, you should have around 45 minutes to one hour to work with the content and incorporate it into your project before it is rendered worthless. After that moment, the content, in its existing shape, will no longer be able to be managed effectively.
On top of this, you have to quickly pour the material after mixing it after it has been done. If you were to leave the material in the can after it had been mixed, it would start to get very hot and begin to congeal inside the can. Because of this, you have to make sure that it is thoroughly mixed, and then you have to pour it as quickly as possible.
