Dec 22 , 2022
Even though things could look dirty, weathered, and rusty right now, you do not need to install a new bathtub in order to recover the luxurious and shiny appearance of when they were brand new. Rather than installing a whole new tub, which can take a lot of time and be complicated, you can breathe new life into your bathroom with tub resurfacing, which is both effective and affordable.
Tub resurfacing, which is both quick and trendy, has swiftly emerged as many homeowners' top option for bringing their bathrooms up to date in the current era. With the help of this concise summary, you will be able to get a head start on renovating your bathroom environment and bidding rust farewell.
Why Bathtubs Get Rusted
Iron in the water is the most prevalent cause of rust in bathtubs, while other factors might contribute to this problem. The iron that would normally be water-soluble is converted into insoluble iron when the water in your tub evaporates.
This process can be sped up by faucets that drip or leak constantly. As soon as that iron is left behind, it will begin to rust because it will become oxidized (exposed to oxygen). This rust can cause harm to your tub as well as discolor it.
In addition to iron, the development of hard water can also cause damage to the surface of your bathtub. This damage can take the form of difficult-to-remove scale and mineral deposits on the surface of your bathtub. The enamel on the surface of your tub can wear away over time, much like the enamel on your teeth can, and it will need to be refinished if you want to keep its glossy, watertight appearance.
Tiled bathtubs and showers risk developing cracked or broken tiles and water damage that can accumulate in the grout and give rise to mold and mildew growth.
This damage to the tub needs to be remedied, and tub resurfacing is a solution that is not only cost-effective but also gives your bathroom a new lease on life. The damage could be mineral-based or simply water-based.
The Operation of Resurfacing the Bathtub
Refinishing a bathtub, shower, or bathroom floor can be done in various methods. The first step in the process involves determining why your tub has rust or mildew, as discussed earlier. If your tub has sustained physical damage, the first step in repairing it can be to replace the tub liner or the broken components of the bathroom hardware.
To lay a solid groundwork for your resurfaces, it will be necessary to either replace or restore the affected area, depending on the severity of the physical damage. To stop the further development of mold and decay, any existing mold will need to be removed before any remediation can take place.
Removing the old grout and replacing any cracked tiles is typically the next step in tiling a bathroom. Sometimes, depending on the layout of your bathroom, you will only need to replace the grout and tiles in certain sections, and other times, you may need to resurface the tiled area. This will depend on the design of your bathroom. Before applying fresh surface coatings, the most crucial step is to patch any leaks that have been discovered.
The next step in the process is your no-spray resurfacing, which, in essence, applies a new top coat to parts of your bathroom that were previously dull, out of date, rusty, and in need of repair. A new top coat, much like putting that clear coat on a car to make it shine, helps tighten your tub's water seal and produces beauty and shine that is easy to clean and maintain. In addition, it makes your tub easier to clean.
Ekopel resurfacing, as well as the elimination of rust
Rust, minerals, and general wear and tear are frequent causes of tub damage. Making your bathtub and shower into works of art can start with repairs and end with an experienced professional refinishing the bathtub. When performing a professional installation, we, Refinished Bath Solutions, resurface tub and surround units by mixing and pouring two Ekopel kits in the order given, beginning at the top of the unit. In order to avoid drip marks on the walls, simultaneous use of two kits is required, and the walls must be leveled out as rapidly as possible. The comprehensive instructions may be found in the product listing for our surround kit.
Made in the USA, safe for the environment, and non-toxic: Ekopel's long-lasting glaze is oil-free and doesn't contain any dangerous ingredients; it also emits no fumes and never peels! Tub surfaces can be brought back to a "like new" dazzling luster by using this product's thick, full-seal coating.
Ekopel can be applied to virtually any bathtub substrate, including cast iron, steel, ceramic, fiberglass, and painted surfaces.
Should one remove the rust first, or can the apply Ekopel over it?
Getting rid of the rust is an absolute necessity. Sand the surface using sandpaper, then thoroughly wash and dry it before applying Ekopel.
What kind of sandpaper is suggested for the preparation step?
For the surface preparation, you should use sandpaper with a grain range of 220-320. You want the texture to be nice and smooth when you touch it. You should still give it a short sanding, even if the surface is relatively smooth. Sanding is an essential stage in the preparation process, so take it. On the market today, there is no better Bathtub Refinishing Kit than Ekopel. It is also the safest and easiest to use.
You can refinish your tub with the help of our DIY-friendly videos, which will lead you through each step of the procedure. If you have a more involved project, our list of certified installers can assist you in finding a qualified professional.
The advantages of resurfacing, renewing, or refinishing your bathtub can be summed up most simply by saying that you will save both time and money due to the process. By opting for tub resurfacing instead, you can avoid making pricey purchases, such as a new bathtub or shower. It not only saves you money on the materials, but it also reduces the amount of time that your bathroom needs to be out of commission while it is being remodeled. The complete removal and reinstallation of these bathroom fixtures demand excessive time and work, which results in high costs.
